×
Crete Latex(I)
DESCRIPTION:
AT-CRETE LATEX (I) is a SBR Polymer which when added to cement mortar or concrete/grout provides good bond strength and water resistance. It is a versatile and economical product for producing polymer concrete.
STANDARDS:
AT-CRETE LATEX (I) as a bonding agent complies with both ASTM C1059 and ASTM C1042
USES:
- AT-CRETE LATEX (I) is ideal for producing excellent polymer concrete.
- AT-CRETE LATEX (I) is used as concrete additive, as repair mortar for plaster and also for treatment of columns, roofs, foundations, rafts, retaining walls, etc.
- It can also be used for waterproofing of overhead tanks, basements, roofs and fixing of bricks/tiles.
- It can be extensively used as bonding agents for cold joints, for old-new and old-old concrete surfaces.
- Especially used at bridge decks, overlaying of any concrete on concrete surface.
- Effective for areas having high humidity or immerged in water.
- Can also be used as a protective coat on concrete plaster.
ADVANTAGES:
- AT-CRETE LATEX (I) is a highly effective multipurpose styrene butadiene rubber (SBR) Polymer for bonding, waterproofing & repair. Key benefits are:
- Excellent crack bridging properties
- Increases the mechanical properties of mortar
- Shows extremely good bonding to bases like concrete, stone, brick etc.
- Corrosion protective properties for saline environment, effectively admixed with concrete results in neat coat/-plaster without any blow holes
- Compatible with all kind of cements-OPC,PPC, SRC,RHC and slag
- Reduces Saltpeter Action on mortar/concrete/Brick
INSTRUCTION FOR USE:
- SURFACE PREPARATION
- Before application of AT-CRETE LATEX (I) check that surface(s) should be clean from loose particles, dust, oil, grease, acids, and other organic solvents.
- APPLICATION
- AT-CRETE LATEX (I), can be applied by brush, broom, spray or by pouring according to the construction requirement. (However while using the product, we recommend to please consult with our technical team for professional support and guidelines).
- Following are some specified examples of application of AT-CRETE LATEX (I)
| APPLICATION TYPE | MIX DESIGN |
| PLASTER MORTAR | SLURRY: AT-CRETE LATEX (I): Water = 1:4 Cement : Sand (Zone II/III): Slurry = 1:2.5:0.40-0.45 (Depending upon the site conditions, application substrate, water absorption of sand and zone, and of course the cement type and consistency ) |
| POLYMER CONCRETE | SLURRY: AT-CRETE LATEX (I): Water = 1:4 FOR THICKNESS UPTO 25 MM Cement : Sand (Zone II/III) : CA10 : Slurry = 1:2.5:4.6:0.43-0.50 FOR THICKNESS OVER 25 MM Cement : Sand ( Zone II/III ) : CA 10 : CA 20 : Slurry = 1:2.5:2.4:1.2:0.42-0.50 (Depending upon the site conditions, application substrate, water absorption of sand and zone, and of course the cement type and consistency ) |
| BONDING AGENT | Cement :AT-CRETE LATEX (I) = 2 : 1 (Ratio may be adjusted to pourable consistency in case of congested reinforcement) |
| CORROSION PROTECTIVE SLURRY | Cement :AT-CRETE LATEX (I) = 2 : 1 |
| INJECTION GROUTING | Cement :AT-CRETE LATEX (I) : Water = 5:0.5:2 |
TECHNICAL DATA:
| COLOUR | Milky White |
| FORM | Liquid |
| pH VALUE | 8-9 |
| MFFT (ºC) | 4 (Minimum Film Forming Temperature –workable, Temperature needed for effective flexible film) |
PACKAGING & STORAGE:
- AT-CRETE LATEX (I) is available in the following pack:
- 500 g / 1 kg / 5 kg / 20 kg / 50 kg / 200 kg PACK
- Shelf life is 12 months in sealed containers as provided
- Protect AT-CRETE LATEX (I) from direct sunlight
- Keep containers sealed and away from heat and cold in a well ventilated area
- Stir material well before use.
HEALTH & SAFETY:
- Protect hands with rubber gloves and eyes with goggles.
- Accidental splashes to the skin or eyes must be rinsed immediately with clean water.
- Store in well-labeled containers.